Zephyr Anzio button blinking slowly: mesh filters at 30 hours, charcoal at 120
These ICON Touch hoods blink one button slowly after 30 hours of fan use for the mesh filters, a reminder that is always on.
Mon–Sat, 8am–8pm
- Filter reminders
- Range hood filter and baffle service
- Source: Zephyr
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Filter button slowly blinking (30 or 120 hours)
actually means.
These ICON Touch hoods blink one button slowly after 30 hours of fan use for the mesh filters, a reminder that is always on. If the charcoal reminder has been enabled for a recirculating installation, another button blinks slowly after 120 hours. All LED indicators blink twice to confirm each reset.
Zephyr range hood display · also shown as mesh filter clean reminder, charcoal filter replace indicator
What to do when Filter button slowly blinking (30 or 120 hours) shows on the range hoodKind of codeFilter reminders
The hood has counted enough hours of fan time to ask for its filters: the mesh or baffle grease filters want a wash, or on a recirculating hood the charcoal filters want replacing. Most hoods count hours rather than measure grease, so the light comes on whether the filters are clean or not, and it stays on until it is reset with the key the manual names. A reminder that returns straight after a reset, or a hood that still pulls weakly with fresh filters, is worth a visit.
Usually leads toRange hood filter and baffle service
Cleaning or replacing what catches grease and odor: mesh and baffle filters, charcoal pads on recirculating hoods, and the grease channel.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeZephyr
Zephyr hoods with unresponsive touch controls, dim lamps or a fan that drifts on without being asked are checked at your home.
SourceZephyr Anzio and Savona use, care and installation guide
Anzio (ZAN) and Savona (ZSA) ICON Touch hoods.
Before you book,
in this order.
Each step comes from Zephyr's own guidance for Filter button slowly blinking (30 or 120 hours) on its range hoods. Follow it to the end: the last card says whether this is a visit.
Note which button is blinking and match it to the reminder in your manual.
Clean the mesh filters or replace the charcoal filters with the hood off.
Hold the blinking button for three seconds (mesh) or two seconds (charcoal) with the hood off; two blinks from all LEDs confirm the reset.
Book a visit if the reminder will not clear.
Still there?
It usually turns into range hood filter and baffle service. Book with the code and the model number.
What not to do
LEDs that blink slowly one after another right after you start delay-off are counting down the 5-minute timer, not asking for filters. A button that blinks with the fan running is not a failed keypad.
What you may
notice with it.
The range hood problems Filter button slowly blinking (30 or 120 hours) tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
Where Filter button slowly blinking (30 or 120 hours) usually leads
Range hood filter and baffle service.
Zephyr
range hoods.
Zephyr hoods with unresponsive touch controls, dim lamps or a fan that drifts on without being asked are checked at your home.
Zephyr range hood repairMore Zephyr codes
Filter reminders on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Zephyr's own words
button indicator will begin to slowly blink indicating it is time to clean the mesh filters.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Anzio (ZAN) and Savona (ZSA) ICON Touch hoods.
Zephyr Filter button slowly blinking (30 or 120 hours) range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Filter button slowly blinking (30 or 120 hours).
Can I clear Filter button slowly blinking (30 or 120 hours) myself?
Is the charcoal reminder on by default on a Zephyr Anzio?
How do I know my Zephyr Anzio reset worked?
Can I turn off the mesh filter reminder on a Zephyr Anzio?
Back to your everyday
Still showing Filter button slowly blinking (30 or 120 hours)?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.