Zephyr
showing A then 1
Clean Air switches the hood on every 4 hours for 10 minutes to move air through the home.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Zephyr
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What A then 1
actually means.
Clean Air switches the hood on every 4 hours for 10 minutes to move air through the home. While it runs, the display shows A and then 1, the speed it uses. Nothing is wrong; the fan starting on its own is the feature doing its job.
Zephyr range hood display · also shown as A1, A, Clean Air
What to do when A then 1 shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
If you want it, leave it; the fan stops again after 10 minutes.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeZephyr
Zephyr hoods with unresponsive touch controls, dim lamps or a fan that drifts on without being asked are checked at your home.
SourceZephyr Help Center: Range Hood Troubleshooting
Zephyr hoods with a single-character display and the Clean Air feature; the help center gives the on/off steps.
Before you book,
in this order.
Each step comes from Zephyr's own guidance for A then 1 on its range hoods. Follow it to the end: the last card says whether this is a visit.
If you want it, leave it; the fan stops again after 10 minutes.
To switch it off, with the hood off hold the on/off button about 5 seconds until the display goes from A to a dash.
If the fan still starts by itself with Clean Air off, try a power reset at the breaker for 5 to 10 minutes, then book a visit if it continues.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
A then 1 is not a numbered error code, and it does not point to a stuck relay. A fan that runs nonstop, not in 10-minute bursts, is a different problem.
What you may
notice with it.
The range hood problems A then 1 tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Zephyr
range hoods.
Zephyr hoods with unresponsive touch controls, dim lamps or a fan that drifts on without being asked are checked at your home.
Zephyr range hood repairMore Zephyr codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Zephyr's own words
This means the Clean Air feature is activated.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Zephyr hoods with a single-character display and the Clean Air feature; the help center gives the on/off steps.
Zephyr A then 1 range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about A then 1.
Can I clear A then 1 myself?
Why does my Zephyr hood turn on in the middle of the night?
How do I turn off Clean Air on a Zephyr?
Does Clean Air wear out my Zephyr blower?
Back to your everyday
Still showing A then 1?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.