RangeHoodeRepair.center (844) 398-3217Mon–Sat, 8am–8pm Book a visit
A stainless baffle grease filter half slid out of the underside of an under-cabinet range hood, a small filter symbol glowing on the hood's control strip.

Zephyr LCD reading CLEAN GREASE FILTERS HOLD FAN- TO RESET

Zephyr's LCD touch controls keep a grease filter reminder that cannot be turned off.

(844) 398-3217

Mon–Sat, 8am–8pm

  • Filter reminders
  • Range hood filter and baffle service
  • Source: Zephyr

Book a visit

Three short steps, about a minute.

or call (844) 398-3217

What CLEAN GREASE FILTERS HOLD FAN- TO RESET
actually means.

Zephyr's LCD touch controls keep a grease filter reminder that cannot be turned off. At 60 fan hours a filter graphic lights on the screen, and pressing a key shows the hood status followed by this sentence. It stays until the reset is done with the hood fully off.

Zephyr range hood display · also shown as grease filter graphic on LCD

What to do when CLEAN GREASE FILTERS HOLD FAN- TO RESET shows on the range hood

Kind of codeFilter reminders

The hood has counted enough hours of fan time to ask for its filters: the mesh or baffle grease filters want a wash, or on a recirculating hood the charcoal filters want replacing. Most hoods count hours rather than measure grease, so the light comes on whether the filters are clean or not, and it stays on until it is reset with the key the manual names. A reminder that returns straight after a reset, or a hood that still pulls weakly with fresh filters, is worth a visit.

Usually leads toRange hood filter and baffle service

Cleaning or replacing what catches grease and odor: mesh and baffle filters, charcoal pads on recirculating hoods, and the grease channel.

Shows up asReading a Range Hood Error Code or Blinking Light

A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.

MakeZephyr

Zephyr hoods with unresponsive touch controls, dim lamps or a fan that drifts on without being asked are checked at your home.

SourceZephyr Tornado II and III use, care and installation guide

Tornado II (AK8227AS, AK8234AS) and Tornado III (AK8340ASX) LCD touch controls.

Before you book,
in this order.

Each step comes from Zephyr's own guidance for CLEAN GREASE FILTERS HOLD FAN- TO RESET on its range hoods. Follow it to the end: the last card says whether this is a visit.

01

Turn the hood off and wash the grease filters as your manual describes.

02

With the whole hood powered off, press and hold FAN- until the message clears.

03

If the text returns straight away, book a visit to have the control checked.

Still there?

It usually turns into range hood filter and baffle service. Book with the code and the model number.

What not to do

The message is not a blower or motor warning. On the ICON Touch LCD models the same reminder may show as scrolling text with a slowly blinking FAN- button instead.

What you may
notice with it.

The range hood problems CLEAN GREASE FILTERS HOLD FAN- TO RESET tends to arrive with. Answer these at the range hood before anyone is booked.

All problems

Before you call

Reading a Range Hood Error Code or Blinking Light

All 7 causes, cheapest first

It also comes with

Close view of the front control strip of a stainless wall-mount chimney range hood on a tiled wall, a few abstract lit segments on its small display and one indicator blinking, the range hood's canopy filling the upper half of the frame. Problem

Reading a Range Hood Error Code or Blinking Light

7 causes, cheapest first

Where CLEAN GREASE FILTERS HOLD FAN- TO RESET usually leads

Range hood filter and baffle service.

Mesh or baffle filters, charcoal pads and the grease channel · lowest.
Book a visit What the job involves

Zephyr
range hoods.

Zephyr hoods with unresponsive touch controls, dim lamps or a fan that drifts on without being asked are checked at your home.

Zephyr range hood repair

More Zephyr codes

FCA then 1FAN- button slowly blinkingClean filters indicator on or flashingFilter button slowly blinking (30 or 120 hours)ACT 390PAIRINGHELLOFilter clean icon blinkingDot flashing in the lower right of the display

Filter reminders on other makes

Bertazzoni FBEST Fan LED bar flashes slowly for 30 seconds after the fan is turned offBlueStar Timer icon blinking, blower offBosch clean grease filterDacor Low button blinkingElica Grease FilterFaber Filter alarm LED on (steady)Falmec Red LED steady on with the fan off
All 56 codes of this kind
A stainless steel wall-mount chimney range hood fixed to a white subway tile wall in a US home kitchen, the range hood's rectangular chimney cover rising straight to the ceiling, soft steam rising from a pot into the canopy, the range hood filling the upper half of the frame, the cooking surface below cropped and out of focus at the bottom edge. Zephyr builds this

Wall-mount range hood

The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.

 A slim stainless under-cabinet range hood mounted beneath white shaker wall cabinets in a US home kitchen, the range hood's two lamps glowing onto steam rising from a simmering pot, the range hood and the cabinets above it filling the upper half of the frame, the cooking surface below cropped and out of focus. Zephyr builds this

Under-cabinet range hood

The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.

 A large stainless island range hood hanging from the ceiling on its four-sided chimney over a kitchen island with a white stone top in a US home, steam rising from a pan into the range hood's canopy, the range hood centered in the upper half of the frame, the burners on the island below cropped and out of focus. Zephyr builds this

Island range hood

The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.

In Zephyr's own words

CLEAN GREASE FILTERS HOLD FAN- TO RESET
Zephyr Tornado II and III use, care and installation guide Zephyr Tornado II and III use, care and installation guide

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Tornado II (AK8227AS, AK8234AS) and Tornado III (AK8340ASX) LCD touch controls.

Zephyr CLEAN GREASE FILTERS HOLD FAN- TO RESET range hood repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A family cooking together under a stainless range hood in a bright kitchen.
For the heart of your home.

Questions
about CLEAN GREASE FILTERS HOLD FAN- TO RESET.

Can I clear CLEAN GREASE FILTERS HOLD FAN- TO RESET myself?
Turn the hood off and wash the grease filters as your manual describes. If it comes back, it needs a visit.
Can I disable the grease filter message on a Zephyr Tornado?
No. Zephyr describes the reminder as always enabled, so the only way to clear it is the reset after cleaning.
Why won't the Zephyr filter message reset?
The reset only works with the entire hood powered off. Holding FAN- while the fan or lights are on does not clear it.
How many hours before the Zephyr Tornado asks again?
Sixty hours of fan use after each reset.

Back to your everyday

Still showing CLEAN GREASE FILTERS HOLD FAN- TO RESET?

Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.

Schedule a repair Call (844) 398-3217
(844) 398-3217 Schedule a repair