Faber intensive speed ending by itself: the boost is timed
Faber's intensive speed is built for short bursts of heavy smoke.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Faber
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Intensive speed drops back after 6 or 10 minutes
actually means.
Faber's intensive speed is built for short bursts of heavy smoke. On the Highlight and Inca Lux Premium it runs for 6 minutes; on the Stilo, holding the high-speed button for 2 seconds starts it for 10 minutes. Afterward the hood returns to the speed you had before, or switches off if it started from off.
Faber range hood display · also shown as INTENSIVE, boost
What to do when Intensive speed drops back after 6 or 10 minutes shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Press intensive again if the smoke is still heavy.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeFaber
A Faber range hood that runs on only one speed, or hums without spinning, gets a visit that starts at its speed control.
SourceFaber Highlight island hood installation, use and care guide
Highlight and Inca Lux Premium: 6 minutes. Stilo and Dama wall hoods: 10 minutes after a 2-second press.
Before you book,
in this order.
Each step comes from Faber's own guidance for Intensive speed drops back after 6 or 10 minutes on its range hoods. Follow it to the end: the last card says whether this is a visit.
Press intensive again if the smoke is still heavy.
Otherwise pick the highest regular speed for longer runs.
If the hood drops speed during ordinary speeds, not just after intensive, book a visit to test the blower and control.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
The drop in speed is not the motor overheating or failing. If intensive never starts at all, the hood may have had its airflow reduced during installation, which disables intensive on some models.
What you may
notice with it.
The range hood problems Intensive speed drops back after 6 or 10 minutes tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Faber
range hoods.
A Faber range hood that runs on only one speed, or hums without spinning, gets a visit that starts at its speed control.
Faber range hood repairMore Faber codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Faber's own words
This speed is timed to run for 6 minutes.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Highlight and Inca Lux Premium: 6 minutes. Stilo and Dama wall hoods: 10 minutes after a 2-second press.
Faber Intensive speed drops back after 6 or 10 minutes range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Intensive speed drops back after 6 or 10 minutes.
Can I clear Intensive speed drops back after 6 or 10 minutes myself?
Why does my Faber slow down after a few minutes on high?
Can I keep a Faber on intensive speed all the time?
Why won't intensive speed start on my Faber?
Back to your everyday
Still showing Intensive speed drops back after 6 or 10 minutes?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.