GE Profile under-cabinet hood lights chasing Lo to Light: Chef Connect pairing
Holding the Light pad for 3 seconds starts Chef Connect pairing.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Lo, Med, Hi and Light backlights flash in sequence
actually means.
Holding the Light pad for 3 seconds starts Chef Connect pairing. The four backlights then flash in sequence until the hood links with a compatible GE cooking appliance, and a successful link is shown by all four flashing together three times before going dark. If nothing pairs within 2 minutes, the hood stops trying.
GE Profile range hood display · also shown as all 4 lights flash three times together
What to do when Lo, Med, Hi and Light backlights flash in sequence shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Start pairing on the GE cooking appliance you want to link, following its own instructions, within 2 minutes.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeGE Profile
GE Profile hoods and downdraft vents get fixed in your kitchen, starting with a check of the breaker and the hood's own switch.
SourceGE / GE Profile range hoods owner's manual 49-2001095 (JVX, PVX7300, PVX7360)
GE Profile PVX7300 and PVX7360 under-the-cabinet hoods with the glass touch panel and Chef Connect (owner's manual 49-2001095). Models with rocker switches have no pairing lights.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Lo, Med, Hi and Light backlights flash in sequence on its range hoods. Follow it to the end: the last card says whether this is a visit.
Start pairing on the GE cooking appliance you want to link, following its own instructions, within 2 minutes.
Watch for all four lights to flash together three times; that confirms the link.
To cancel, hold the Light pad for 3 seconds and then turn the hood off.
If the sequence starts on its own or the hood never pairs with a compatible appliance, book a visit.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
The chasing lights are not a failing board, and the fan still works normally from its pads. A steady on-off blink of every backlight together is a different state, the Default Settings Mode.
What you may
notice with it.
The range hood problems Lo, Med, Hi and Light backlights flash in sequence tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
GE Profile
range hoods.
GE Profile hoods and downdraft vents get fixed in your kitchen, starting with a check of the breaker and the hood's own switch.
GE Profile range hood repairMore GE Profile codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In GE Profile's own words
The backlight for the Lo – Med – Hi – Light will flash in that sequence until the hood is paired
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile PVX7300 and PVX7360 under-the-cabinet hoods with the glass touch panel and Chef Connect (owner's manual 49-2001095). Models with rocker switches have no pairing lights.
GE Profile Lo, Med, Hi and Light backlights flash in sequence range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Lo, Med, Hi and Light backlights flash in sequence.
Can I clear Lo, Med, Hi and Light backlights flash in sequence myself?
How do I stop the GE Profile hood lights from flashing in a row?
How do I know my GE Profile hood paired with Chef Connect?
My GE Profile hood paired, so why does the fan stay off when I cook?
Back to your everyday
Still showing Lo, Med, Hi and Light backlights flash in sequence?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.