Red light above Reset Filter on a GE Profile designer wall hood
The UVW9301 and UVW9361 designer hoods time filter use and light a red LED above Reset Filter when service is due.
Mon–Sat, 8am–8pm
- Filter reminders
- Range hood filter and baffle service
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Red LED above Reset Filter
actually means.
The UVW9301 and UVW9361 designer hoods time filter use and light a red LED above Reset Filter when service is due. Holding the pad for 3 seconds turns it off, and a tap starts the count again. On a recirculating install, the charcoal filter supplied with the hood is replaced, not cleaned, when this LED comes on.
GE Profile range hood display · also shown as Reset Filter indicator
What to do when Red LED above Reset Filter shows on the range hoodKind of codeFilter reminders
The hood has counted enough hours of fan time to ask for its filters: the mesh or baffle grease filters want a wash, or on a recirculating hood the charcoal filters want replacing. Most hoods count hours rather than measure grease, so the light comes on whether the filters are clean or not, and it stays on until it is reset with the key the manual names. A reminder that returns straight after a reset, or a hood that still pulls weakly with fresh filters, is worth a visit.
Usually leads toRange hood filter and baffle service
Cleaning or replacing what catches grease and odor: mesh and baffle filters, charcoal pads on recirculating hoods, and the grease channel.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeGE Profile
GE Profile hoods and downdraft vents get fixed in your kitchen, starting with a check of the breaker and the hood's own switch.
SourceGE Appliances Smart Designer wall hoods owner's manual (UVW9301, UVW9361)
Smart Designer wall-mount hoods UVW9301 and UVW9361 (universal models GE lists under the GE Profile brand), owner's manual for the designer wall hoods.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Red LED above Reset Filter on its range hoods. Follow it to the end: the last card says whether this is a visit.
Wash the metal grease filters; if the hood recirculates, fit a new charcoal filter as well.
Hold Reset Filter for 3 seconds to turn the red LED off.
Tap Reset Filter once more to restart the filter timer.
If the LED will not go out, book a visit.
Still there?
It usually turns into range hood filter and baffle service. Book with the code and the model number.
What not to do
The red LED does not warn of a blower or wiring problem. The Wi-Fi symbol that blinks for 3 seconds above the clock is a separate connect signal.
What you may
notice with it.
The range hood problems Red LED above Reset Filter tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
Where Red LED above Reset Filter usually leads
Range hood filter and baffle service.
GE Profile
range hoods.
GE Profile hoods and downdraft vents get fixed in your kitchen, starting with a check of the breaker and the hood's own switch.
GE Profile range hood repairMore GE Profile codes
Filter reminders on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In GE Profile's own words
The red LED indicator above the Reset Filter pad turns on as a reminder to change /clean the filter.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Smart Designer wall-mount hoods UVW9301 and UVW9361 (universal models GE lists under the GE Profile brand), owner's manual for the designer wall hoods.
GE Profile Red LED above Reset Filter range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Red LED above Reset Filter.
Can I clear Red LED above Reset Filter myself?
How do I turn off the red Reset Filter light on my GE Profile hood?
Can I clean the charcoal filter when the Reset Filter light comes on?
Does the Reset Filter light mean my GE Profile hood is losing suction?
Back to your everyday
Still showing Red LED above Reset Filter?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.