Monogram professional hood: HIGH light blinking
Pressing and holding HIGH for 3 seconds switches the QuietBoost blower to Boost, its top speed.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Monogram
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What HIGH pad LED blinking
actually means.
Pressing and holding HIGH for 3 seconds switches the QuietBoost blower to Boost, its top speed. The HIGH LED blinks on and off while Boost is active, and Boost lasts 15 minutes. The heat sensor can also send the blower to Boost on its own.
Monogram range hood display · also shown as Boost
What to do when HIGH pad LED blinking shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Let Boost run if there is heavy smoke or steam; it ends after 15 minutes.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeMonogram
Monogram hoods and hood inserts are repaired in place, working from the control panel back to the blower and the damper.
SourceMonogram stainless steel professional vent hoods with QuietBoost blower owner's manual 49-2000705
Monogram ZVW1360 and ZVW1480 professional hoods, owner's manual 49-2000705.
Before you book,
in this order.
Each step comes from Monogram's own guidance for HIGH pad LED blinking on its range hoods. Follow it to the end: the last card says whether this is a visit.
Let Boost run if there is heavy smoke or steam; it ends after 15 minutes.
Press POWER to switch the fan off if you want to stop sooner.
If Boost came on by itself, turn down the burners: the heat sensor may have triggered it.
If the HIGH light blinks with the burners off and the hood cool, book a visit.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
A blinking HIGH light does not warn of a failing motor. A fan that cuts in and out on its own is different; Monogram links that to the motor overheating and asks for clean filters first.
What you may
notice with it.
The range hood problems HIGH pad LED blinking tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Monogram
range hoods.
Monogram hoods and hood inserts are repaired in place, working from the control panel back to the blower and the damper.
Monogram range hood repairMore Monogram codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Monogram's own words
Press and hold the HIGH pad for 3 seconds to activate the BOOST speed that will run for 15 minutes.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Monogram ZVW1360 and ZVW1480 professional hoods, owner's manual 49-2000705.
Monogram HIGH pad LED blinking range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about HIGH pad LED blinking.
Can I clear HIGH pad LED blinking myself?
Why is my Monogram hood roaring with the HIGH light blinking?
How long does Boost last on a Monogram professional hood?
Can the Monogram hood go to Boost by itself?
Back to your everyday
Still showing HIGH pad LED blinking?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.