RangeHoodeRepair.center (844) 398-3217Mon–Sat, 8am–8pm Book a visit
The glass touch keypad on the front edge of a stainless island range hood, its speed keys dark and one key softly blinking, the kitchen island below out of focus.

XO button blinking five seconds: ready to pair a remote

XO remotes must be synchronized with the hood.

(844) 398-3217

Mon–Sat, 8am–8pm

  • Control board and keypad
  • Range hood control board repair
  • Source: XO

Book a visit

Three short steps, about a minute.

or call (844) 398-3217

What Button blinking for 5 seconds
actually means.

XO remotes must be synchronized with the hood. Holding the hood's button for four seconds with the fan off makes it blink for five seconds, and pressing any remote key during that time pairs the two.

XO range hood display · also shown as remote pairing

What to do when Button blinking for 5 seconds shows on the range hood

Kind of codeControl board and keypad

The electronics that read the keys and switch the fan and the lights have flagged a problem with themselves: a key the board thinks is held down, a membrane keypad worn through or soaked with grease and steam, a speed relay that stuck closed, or a board that lost its settings in a surge. A breaker reset clears a one-off; a code that returns, or a hood that ignores its keys entirely, needs the keypad and the board tested.

Usually leads toRange hood control board repair

Testing and replacing the board behind a keypad or touch strip: the relays for each speed and the lights, the timers and the power supply.

Shows up asReading a Range Hood Error Code or Blinking Light

A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.

MakeXO

XO range hoods are repaired on a home call, and a cold draft through the hood or a sluggish fan are both good reasons to book.

SourceXO XOI22SC / XOI28SC insert manual

XO hoods sold with or fitted for the XOVREMOTE1 remote, including the XOI22SC/XOI28SC inserts and the XOCEILING36S/42S ceiling vents.

Before you book,
in this order.

Each step comes from XO's own guidance for Button blinking for 5 seconds on its range hoods. Follow it to the end: the last card says whether this is a visit.

01

With the hood not running, hold the hood button for four seconds.

02

While it blinks, press any button on the remote.

03

If pairing fails, fit a fresh battery in the remote and repeat; if it still fails, book a visit.

Still there?

It usually turns into range hood control board repair. Book with the code and the model number.

What not to do

The blinking is the pairing window, not a keypad failure. A remote that stops working after a power cut may simply need to be synchronized again.

What you may
notice with it.

The range hood problems Button blinking for 5 seconds tends to arrive with. Answer these at the range hood before anyone is booked.

All problems

Before you call

Reading a Range Hood Error Code or Blinking Light

All 7 causes, cheapest first

It also comes with

Close view of the front control strip of a stainless wall-mount chimney range hood on a tiled wall, a few abstract lit segments on its small display and one indicator blinking, the range hood's canopy filling the upper half of the frame. Problem

Reading a Range Hood Error Code or Blinking Light

7 causes, cheapest first

Where Button blinking for 5 seconds usually leads

Range hood control board repair.

Control board with its relays and power supply · moderate.
Book a visit What the job involves

XO
range hoods.

XO range hoods are repaired on a home call, and a cold draft through the hood or a sluggish fan are both good reasons to book.

XO range hood repair

More XO codes

LED flashing (Power Boost)Control blinks 3 timesClean Air indicator blinkingDisplay flashing after power loss

Control board and keypad on other makes

Bosch CONNECT and 2 flashingFisher & Paykel Wi-Fi button flashing whiteGaggenau Ring flashes yellow and magentaGE Profile A button collar does not light when pressedMiele 2 and 3 flashingThermador CONNECT and 2 flashing
All 9 codes of this kind
A stainless steel wall-mount chimney range hood fixed to a white subway tile wall in a US home kitchen, the range hood's rectangular chimney cover rising straight to the ceiling, soft steam rising from a pot into the canopy, the range hood filling the upper half of the frame, the cooking surface below cropped and out of focus at the bottom edge. XO builds this

Wall-mount range hood

The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.

 A slim stainless under-cabinet range hood mounted beneath white shaker wall cabinets in a US home kitchen, the range hood's two lamps glowing onto steam rising from a simmering pot, the range hood and the cabinets above it filling the upper half of the frame, the cooking surface below cropped and out of focus. XO builds this

Under-cabinet range hood

The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.

 A large stainless island range hood hanging from the ceiling on its four-sided chimney over a kitchen island with a white stone top in a US home, steam rising from a pan into the range hood's canopy, the range hood centered in the upper half of the frame, the burners on the island below cropped and out of focus. XO builds this

Island range hood

The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.

In XO's own words

press and hold BUTTON on the hood for 4 seconds -the button should start to blink for 5 seconds.
XO XOI22SC / XOI28SC insert manual XO XOCEILING36S / XOCEILING42S ceiling vent manual

Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. XO hoods sold with or fitted for the XOVREMOTE1 remote, including the XOI22SC/XOI28SC inserts and the XOCEILING36S/42S ceiling vents.

XO Button blinking for 5 seconds range hood repair,
where we come out.

The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.

All service areas

Tampa BayFL · 31 areas

OrlandoFL · 30 areas

Miami / South FloridaFL · 47 areas

New York MetroNY · 75 areas

HoustonTX · 36 areas

ChicagoIL · 50 areas

Los AngelesCA · 95 areas

San DiegoCA · 31 areas

San Francisco Bay AreaCA · 74 areas

A family cooking together under a stainless range hood in a bright kitchen.
For the heart of your home.

Questions
about Button blinking for 5 seconds.

Can I clear Button blinking for 5 seconds myself?
With the hood not running, hold the hood button for four seconds. If it comes back, it needs a visit.
Why won't my XO remote work after installation?
It has to be paired first: hold the hood button four seconds, then press a remote key while it blinks.
My XO ceiling vent ignores the remote. What now?
Pair it again, and if the hood still ignores it, try a new battery before booking a visit.
Does pairing change any settings on my XO hood?
No, it only links the remote to the hood.

Back to your everyday

Still showing Button blinking for 5 seconds?

Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.

Schedule a repair Call (844) 398-3217
(844) 398-3217 Schedule a repair