Falmec + light flashing: speed 4 is on for a few minutes
On Falmec keypads with the SRS system disabled, speed 4 is shown by the + key flashing.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Falmec
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What "+" LED flashing (speed 4)
actually means.
On Falmec keypads with the SRS system disabled, speed 4 is shown by the + key flashing. It is a short boost for heavy smoke and returns to speed 3 by itself after a few minutes.
Falmec range hood display · also shown as speed 4, boost
What to do when "+" LED flashing (speed 4) shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Press + again later if you need another boost.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeFalmec
Falmec hoods are inspected where they hang, including the brackets and fasteners that carry their weight.
SourceFalmec Eros under-cabinet hood instructions booklet (USA)
Eros, Vulcano Plus NRS, Lumen and similar Falmec keypads; the Massimo Pro NRS booklet says the same of speed 4 without the flashing +.
Before you book,
in this order.
Each step comes from Falmec's own guidance for "+" LED flashing (speed 4) on its range hoods. Follow it to the end: the last card says whether this is a visit.
Press + again later if you need another boost.
Stay on speed 3 for long cooking sessions.
If the hood drops speed without speed 4 being selected, book a visit to check the blower.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
The drop from 4 to 3 is not overheating or a failing motor. If speed 4 never comes on, the SRS speed limit may be enabled, which caps the hood at speed 3 or 2.
What you may
notice with it.
The range hood problems "+" LED flashing (speed 4) tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Falmec
range hoods.
Falmec hoods are inspected where they hang, including the brackets and fasteners that carry their weight.
Falmec range hood repairMore Falmec codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Falmec's own words
Speed 4 is only active for a few minutes, then it goes back to speed 3.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Eros, Vulcano Plus NRS, Lumen and similar Falmec keypads; the Massimo Pro NRS booklet says the same of speed 4 without the flashing +.
Falmec "+" LED flashing (speed 4) range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about "+" LED flashing (speed 4).
Can I clear "+" LED flashing (speed 4) myself?
Why does my Falmec slow down after a few minutes?
Why can't I get speed 4 on my Falmec?
Is a flashing + on my Falmec a warning?
Back to your everyday
Still showing "+" LED flashing (speed 4)?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.