Viking wall hood blower starts on high by itself
Viking fits a heat sensor thermostat to its wall hoods.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Viking
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Blower comes on at high by itself
actually means.
Viking fits a heat sensor thermostat to its wall hoods. When it senses excessive heat above the burners, it turns the blower on at high or raises it from a lower speed. Once the temperature is back to normal, the blower returns to its original setting.
Viking range hood display · also shown as heat sensor thermostat
What to do when Blower comes on at high by itself shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Turn down the burners or griddle, and let the hood cool.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeViking
Viking range hoods that have grown loud, weak or dark are looked at in place, from the lamps and switches to the blower overhead.
SourceViking 3 Series chimney wall hoods RVCH330/RVCH336 use and care
Viking 3 Series RVCH chimney wall hoods and 5 Series wall hoods (heat sensor listed on the 10-inch VWH specification sheet and the 5 Series use and care guide).
Before you book,
in this order.
Each step comes from Viking's own guidance for Blower comes on at high by itself on its range hoods. Follow it to the end: the last card says whether this is a visit.
Turn down the burners or griddle, and let the hood cool.
Leave the blower running until it drops back by itself.
Before cleaning, disconnect the hood's power, since the sensor can start the blower.
If the blower keeps running on high with the burners off and the hood cool, book a visit.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
A blower on high by itself is not a stuck knob or failed switch while the area is hot. If there is flame in the pan or the hood, treat it as a grease fire: burner off, no water, lid on the pan, and leave and call 911 if it spreads to the hood or cabinets.
What you may
notice with it.
The range hood problems Blower comes on at high by itself tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Viking
range hoods.
Viking range hoods that have grown loud, weak or dark are looked at in place, from the lamps and switches to the blower overhead.
Viking range hood repairMore Viking codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Viking's own words
If the blower is OFF - the sensor turns the blower on to HIGH speed.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Viking 3 Series RVCH chimney wall hoods and 5 Series wall hoods (heat sensor listed on the 10-inch VWH specification sheet and the 5 Series use and care guide).
Viking Blower comes on at high by itself range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Blower comes on at high by itself.
Can I clear Blower comes on at high by itself myself?
Why did my Viking hood fan start while I was wiping it down?
Can I turn the heat sensor off on my Viking hood?
How do I know the heat sensor on my Viking hood has failed?
Back to your everyday
Still showing Blower comes on at high by itself?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.