Faber lights all flashing two or three times: a setting was confirmed
On the Inca Lux Premium, a long press with the motor off either switches the charcoal alarm on, confirmed by all LEDs flashing twice, or resets the filter alarms, confirmed by three flashes.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Faber
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What All LEDs flash two or three times
actually means.
On the Inca Lux Premium, a long press with the motor off either switches the charcoal alarm on, confirmed by all LEDs flashing twice, or resets the filter alarms, confirmed by three flashes. The Highlight uses its S1 light the same way. It is feedback, not a warning.
Faber range hood display · also shown as all LED's flash twice, all LED's flash 3 times
What to do when All LEDs flash two or three times shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Think back to which button was held: speed 2 with the lights on is the charcoal alarm switch, speed 3 with everything off is the filter reset.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeFaber
A Faber range hood that runs on only one speed, or hums without spinning, gets a visit that starts at its speed control.
SourceFaber Inca Lux Premium insert installation, use and care guide
Inca Lux Premium insert; the Highlight confirms the same actions through the S1 LED.
Before you book,
in this order.
Each step comes from Faber's own guidance for All LEDs flash two or three times on its range hoods. Follow it to the end: the last card says whether this is a visit.
Think back to which button was held: speed 2 with the lights on is the charcoal alarm switch, speed 3 with everything off is the filter reset.
If you did not mean to enable the charcoal alarm, repeat the long press; the LEDs stay lit for a second to show it is off.
If the lights flash with nobody touching the keys, book a visit to check the keypad.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
The short flash burst is not the filter alarm, which stays on or keeps blinking. It is also different from the long all-LED flash that opens the CFM adjustment menu.
What you may
notice with it.
The range hood problems All LEDs flash two or three times tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Faber
range hoods.
A Faber range hood that runs on only one speed, or hums without spinning, gets a visit that starts at its speed control.
Faber range hood repairMore Faber codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Under-cabinet range hood
The slim hood screwed to the bottom of the wall cabinet over the burners, venting up through that cabinet or back through the wall, or cleaning the air and returning it to the room.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
In Faber's own words
All LED’s flash twice (alarm activated).
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Inca Lux Premium insert; the Highlight confirms the same actions through the S1 LED.
Faber All LEDs flash two or three times range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about All LEDs flash two or three times.
Can I clear All LEDs flash two or three times myself?
Why did my Faber flash all its lights and then go back to normal?
How do I switch off the charcoal alarm on a Faber insert?
Is flashing on all the Faber keys a sign of a bad board?
Back to your everyday
Still showing All LEDs flash two or three times?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.