BlueStar Boost icon blinking: seven minutes at full power
Boost is the top setting on BlueStar's push-button panel.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: BlueStar
Book a visit
Three short steps, about a minute.
or call (844) 398-3217
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Boost icon blinking
actually means.
Boost is the top setting on BlueStar's push-button panel. While it is on, the icon blinks, and after seven minutes the control moves the blower to high speed by itself.
BlueStar range hood display · also shown as Boost
What to do when Boost icon blinking shows on the range hoodKind of codeMode, not a failure
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
Usually leads toNo repair
Use Boost for heavy smoke or searing, and expect it to end after seven minutes.
Shows up asReading a Range Hood Error Code or Blinking Light
A range hood error code may appear as letters and numbers on a display, a light that blinks in a pattern, a filter reminder that will not clear, or a beep with the fan refusing to start.
MakeBlueStar
When a BlueStar range hood drips grease or leaves smoke hanging over the burners, the visit starts at its baffles and the channel that drains them.
SourceBlueStar wall hoods installation and use & care manual, 197299 Rev 2 (hoods from May 2020)
BlueStar wall hoods covered by manual 197299 (May 2020 onward), with in-hood, remote external or in-line blowers.
Before you book,
in this order.
Each step comes from BlueStar's own guidance for Boost icon blinking on its range hoods. Follow it to the end: the last card says whether this is a visit.
Use Boost for heavy smoke or searing, and expect it to end after seven minutes.
Press Boost again if you still need it.
If Boost does not raise the blower speed at all, book a visit to check the blower and its wiring.
Cleared?
The code is gone and the blower pulls steam up on every speed again without a new part. If it returns this week, or the filter reminder keeps coming back right after a cleaning, mention it in the booking.
What not to do
The blinking icon is not a warning, and the step down to high is timed rather than caused by heat. On hoods with a remote roof or in-line blower, the extra noise of Boost comes from outside the hood.
What you may
notice with it.
The range hood problems Boost icon blinking tends to arrive with. Answer these at the range hood before anyone is booked.
All problems
No repair indicated
Nothing to repair.
The hood is doing something it was told to do, not wearing out: a delay-off timer that keeps the blower running for some minutes after the burners go off, a heat sentry that starts the fan by itself when it senses a hot pan, a Sabbath setting that locks the keys and dims the lights, or a link to the cooking surface that sets the speed on its own. No part is needed; a key sequence from the manual, or simply waiting, ends it.
BlueStar
range hoods.
When a BlueStar range hood drips grease or leaves smoke hanging over the burners, the visit starts at its baffles and the channel that drains them.
BlueStar range hood repairMore BlueStar codes
Mode, not a failure on other makes
Wall-mount range hood
The chimney hood fixed to a bare stretch of wall above the burners, its canopy catching the rising smoke while a telescoping cover hides the duct that climbs to the ceiling.
Island range hood
The hood that hangs from the ceiling over burners set into a kitchen island, open on all four sides, with its duct and wiring hidden inside a chimney that drops from above.
Range hood insert
The working core of a custom hood: a steel liner or power pack carrying the blower, filters, lights and controls, fitted inside a hood built of wood, plaster or metal by a cabinetmaker.
In BlueStar's own words
After 7 minutes of operation, the blower will automatically move to high speed (C).
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. BlueStar wall hoods covered by manual 197299 (May 2020 onward), with in-hood, remote external or in-line blowers.
BlueStar Boost icon blinking range hood repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Boost icon blinking.
Can I clear Boost icon blinking myself?
Why does my BlueStar hood drop out of Boost?
Is Boost louder on a BlueStar with a roof blower?
Can I keep a BlueStar on Boost for a long sear?
Back to your everyday
Still showing Boost icon blinking?
Three things make the booking useful: the letters or blink pattern exactly as they showed, the full model number from the label behind the filters, and whether the fan still moves air on every speed. With those, the technician arrives with half the answer already worked out.